Call Today

 

In this article down the page you can find some excellent information and facts in regards to Installing A Bathtub.

Mounting a bathtub isn't precisely brain surgery, but it does require solid plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a reasonably difficult job. If the old tub is readily easily accessible, the job can move easily; if you need to open up a wall to get rid of the old bathtub as well as place the brand-new tub, the job is a lot harder. In either instance, the task is within a home handyman's skills, although you will certainly need an assistant to vacate the old tub and also embeded in the new one. Make sure you have actually qualified on your own for the task as well as are comfortable attempting it. Rather than hiring a specialist to take over a halfway-completed task, it is much better to consider using one prior to you begin. Chances are you might require a specialist plumber to make tube links.
This article will assist you install a brand-new bath tub in your bathroom if you have actually currently acquired a new bathtub and also do not need to alter the plan of your previous water supply pipelines.
Your tools as well as material list ought to consist of the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Removing Old Touches

If you require to change old faucets with new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing faucets can be fairly bothersome because of the restricted accessibility that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the faucets. Have a towel prepared for the staying water that will come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, after that you will certainly require a plastic port to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washers are in place between the faucet and the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous kind ought to be attached to the faucet finishes first, tightening up only by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.

 

 

Installing the Bathtub

Utilizing both wooden boards under its feet, position the tub in the needed position. The wooden boards are useful in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bath tub till the level checks out level.
To set up faucets, fit all-time low of the outermost versatile faucet port to the ideal supply pipeline by making a compression sign up with; then do the same for the various other tap.
Turn on the supply of water as well as check all joints and new pipework for leaks as well as tighten them if needed. Fill the bath tub as well as additionally examine the overflow electrical outlet and the regular outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's instruction manual. Tiling and sealing around the tub ought to wait until the bathtub has actually been utilized at least when as this will resolve it right into its last setting.

 

 

Getting ready for the Installation

Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps device to stop strain on the bathtub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be suited its last placement.

 

 

Tiling Around the Tub

In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to split a stiff seal, causing the water to penetrate the wall in between the bath and the tiling, causing difficulties with moisture and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and also can securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Remember to constantly fill up the tub with water before sealing, to permit the activity experienced when the bathtub is in use. The sealer can crack relatively early if you do not consider this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is advisable to fit the floor tiles making use of waterproof or water-proof sticky and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

As a passionate person who reads about How to Install a Bathtub Yourself, I was thinking sharing that excerpt was essential. So long as you appreciated our post kindly make sure you remember to share it. Thanks for your time invested reading it.

Book With Us Today!